Aqua Logic AQL-PS-4 Manual de usuario

Aqua Logic Programming Flow ChartAqua LogicAqua LogicAqua LogicAqua LogicAqua LogicAutomation and ChlorinationInstallation Manualfor modelsAQL-PS-4 AQ

Wired Remote ControlsUp to 3 wired remote controls can be installed. See “Electrical Wiring” (page 19) for instructions onrunning the cable from the

Optional Base StationThe optional base station, Goldline part number AQL-BASE-RF or AQL2-BASE-RF, must be installedif any wireless remote control is u

3. Plumbing“Standard” Pool/Spa system configurationThese systems use a single filter pump and filter. Pool or spa operation is controlled by two 3-wa

“Dual Equipment - Separate Heaters” for Pool/Spa configurationThese systems have 2 complete sets of equipment (filter pump, filter, heater)—1 set for

3. The solar sensor should be installed on the spa loop prior to the heater and will display the spatemperature whenever the “Spa Filter” pump is runn

2. The water sensor should be installed on the pool loop prior to the heater(s) and will display thepool temperature whenever the “Pool Filter” pump i

4. Electrical WiringThe Aqua Logic Control Center and PS-16 Expansion Unit require both high and low voltage connec-tions. Low voltage connections w

General Purpose OutletIf desired, a duplex receptacle with weatherproof cover (supplied by installer) may be installed in theknockouts on the lower ri

Two speed filter pump: Requires 2 relays (FILTER plus one of the AUX relays) for proper operation ofboth speeds. !IMPORTANT: Be sure to follow the

The manuals supplied with most heaters also include specific wiring instructions for connecting the heaterto an external control (usually identified a

IMPORTANT SAFETY INSTRUCTIONSWhen using this electrical equipment, basic safety precautions should always befollowed, including the following:•READ AN

Hayward HeatersRefer to the instructions in the heater manual for “2-wire Remote Thermostat” operation under “RemoteControl Connections” and the diagr

Raypak RP2100 Pool/Spa Heater1. Turn power off to heater.2. Push the mode button to “spa” mode.3. Set the temperature to the maximum.4. Push the m

Base StationPlug in the pigtail connector from the wireless base station into the “wireless” connector on the main PCBin the Aqua Logic control unit.P

Base StationPlug in the pigtail connector from the wireless base station into the “wireless” connector on the main PCBin the Aqua Logic control unit.P

Raypak RP2100 Pool/Spa Heater1. Turn power off to heater.2. Push the mode button to “spa” mode.3. Set the temperature to the maximum.4. Push the m

Hayward HeatersRefer to the instructions in the heater manual for “2-wire Remote Thermostat” operation under “RemoteControl Connections” and the diagr

The manuals supplied with most heaters also include specific wiring instructions for connecting the heaterto an external control (usually identified a

Two speed filter pump: Requires 2 relays (FILTER plus one of the AUX relays) for proper operation ofboth speeds. !IMPORTANT: Be sure to follow the

General Purpose OutletIf desired, a duplex receptacle with weatherproof cover (supplied by installer) may be installed in theknockouts on the lower ri

4. Electrical WiringThe Aqua Logic Control Center and PS-16 Expansion Unit require both high and low voltage connec-tions. Low voltage connections w

Table of ContentsIntroduction Before You Begin... 1Installation Steps...

2. The water sensor should be installed on the pool loop prior to the heater(s) and will display thepool temperature whenever the “Pool Filter” pump i

3. The solar sensor should be installed on the spa loop prior to the heater and will display the spatemperature whenever the “Spa Filter” pump is runn

“Dual Equipment - Separate Heaters” for Pool/Spa configurationThese systems have 2 complete sets of equipment (filter pump, filter, heater)—1 set for

3. Plumbing“Standard” Pool/Spa system configurationThese systems use a single filter pump and filter. Pool or spa operation is controlled by two 3-wa

Optional Base StationThe optional base station, Goldline part number AQL-BASE-RF or AQL2-BASE-RF, must be installedif any wireless remote control is u

Wired Remote ControlsUp to 3 wired remote controls can be installed. See “Electrical Wiring” (page 19) for instructions onrunning the cable from the

2. Mounting the EquipmentAqua Logic Control CenterThe Aqua Logic is contained in a raintight enclosure that is suitable for outdoor mounting. The co

Pool Sizing FormulaType of Salt to UseIt is important to use only sodium chloride (NaCl) salt

Gallons and (Liters) of Pool/Spa water12,000 14,000 16,00018,00020,00022,00032,00024,00034,00026,00036,00028,00038,00030,00040,000Current salt level(4

ºC ºF TiCalcuimHardnessCiTot alAlkalinityAi53606676849410312161924293439.3.4.5.6.7.8.9How to use: Measure pool pH, temperature, calcium h

IntroductionBefore You BeginWhat’s IncludedBefore attempting to install the Aqua Logic system, check that the following components have beenincluded i

NOTE: Before installing this product as part of a saline water purification system in a pool or spa usingnatural stone for coping or for immediately a

IntroductionBefore You BeginWhat’s IncludedBefore attempting to install the Aqua Logic system, check that the following components have beenincluded i

Table of ContentsIntroduction Before You Begin... 1Installation Steps...

IMPORTANT SAFETY INSTRUCTIONSWhen using this electrical equipment, basic safety precautions should always befollowed, including the following:•READ AN

Aqua Logic Programming Flow ChartAqua LogicAqua LogicAqua LogicAqua LogicAqua LogicAutomation and ChlorinationInstallation Manualfor modelsAQL-PS-4 AQ

NOTE: Before installing this product as part of a saline water purification system in a pool or spa usingnatural stone for coping or for immediately a

ºC ºF TiCalcuimHardnessCiTot alAlkalinityAi53606676849410312161924293439.3.4.5.6.7.8.9How to use: Measure pool pH, temperature, calcium h

Gallons and (Liters) of Pool/Spa water12,000 14,000 16,00018,00020,00022,00032,00024,00034,00026,00036,00028,00038,00030,00040,000Current salt level(4

Pool Sizing FormulaType of Salt to UseIt is important to use only sodium chloride (NaCl) salt

2. Mounting the EquipmentAqua Logic Control CenterThe Aqua Logic is contained in a raintight enclosure that is suitable for outdoor mounting. The co